NHH-4565C-R2B
6-port sector antenna, 2x 698–896 MHz 45° HPBW and 4x 1695–2360 MHz 65° HPBW, 2x RETs and 2x SBTs. Both high bands share the same electrical tilt.
Specifications
Features and Benefits
- Internal SBT on low and high band allow remote RET control from the radio over the RF jumper cable
- Separate RS-485 RET input/output for low and high band
- One LB RET and one HB RET. Both high bands are controlled by one RET to ensure same tilt level for 4x Rx or 4x MIMO
- Hybrid antenna with narrow beamwidth on the low band for superior interference mitigation on the LB and 65° beamwidth on the high band which allows maintaining the good signal coverage at the cell edge for the high band
Specifications
General Specifications
Antenna Type | Sector |
Band | Multiband |
Color | Light Gray (RAL 7035) |
Grounding Type | RF connector body grounded to reflector and mounting bracket |
Performance Note | Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN |
Radome Material | Fiberglass, UV resistant |
Radiator Material | Aluminum | Low loss circuit board |
Reflector Material | Aluminum |
RF Connector Interface | 4.3-10 Female |
RF Connector Location | Bottom |
RF Connector Quantity, high band | 4 |
RF Connector Quantity, low band | 2 |
RF Connector Quantity, total | 6 |
Remote Electrical Tilt (RET) Information
RET Interface | 8-pin DIN Female | 8-pin DIN Male |
RET Interface, quantity | 2 female | 2 male |
Input Voltage | 10–30 Vdc |
Internal Bias Tee | Port 1 | Port 3 |
Internal RET | High band (1) | Low band (1) |
Power Consumption, idle state, maximum | 1 W |
Power Consumption, normal conditions, maximum | 10 W |
Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
Width | 457 mm | 17.992 in |
Depth | 178 mm | 7.008 in |
Length | 2437 mm | 95.945 in |
Net Weight, without mounting kit | 40 kg | 88.185 lb |
Array Layout
Click on image to enlarge. |
Port Configuration
Click on image to enlarge. |
Electrical Specifications
Impedance | 50 ohm |
Operating Frequency Band | 698 – 896 MHz | 1695 – 2360 MHz |
Polarization | ±45° |
Total Input Power, maximum | 800 W @ 50 °C |
Electrical Specifications
Frequency Band, MHz | 698–806 | 806–896 | 1695–1880 | 1850–1990 | 1920–2200 | 2300–2360 |
Gain, dBi | 17.9 | 18.2 | 17.6 | 18.0 | 18.3 | 18.7 |
Beamwidth, Horizontal, degrees | 47 | 42 | 62 | 62 | 66 | 66 |
Beamwidth, Vertical, degrees | 9 | 8.1 | 5.7 | 5.3 | 5 | 4.5 |
Beam Tilt, degrees | 0–10 | 0–10 | 0–8 | 0–8 | 0–8 | 0–8 |
USLS (First Lobe), dB | 18 | 21 | 17 | 19 | 20 | 20 |
Front-to-Back Ratio at 180°, dB | 33 | 39 | 33 | 35 | 35 | 35 |
Isolation, Cross Polarization, dB | 25 | 25 | 25 | 25 | 25 | 25 |
Isolation, Inter-band, dB | 30 | 30 | 28 | 28 | 28 | 28 |
VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
PIM, 3rd Order, 2 x 20 W, dBc | -153 | -153 | -153 | -153 | -153 | -153 |
Input Power per Port at 50°C, maximum, watts | 300 | 300 | 250 | 250 | 250 | 200 |
Electrical Specifications, BASTA
Frequency Band, MHz | 698–806 | 806–896 | 1695–1880 | 1850–1990 | 1920–2200 | 2300–2360 |
Gain by all Beam Tilts, average, dBi | 17.6 | 18.1 | 17.1 | 17.7 | 18.0 | 18.4 |
Gain by all Beam Tilts Tolerance, dB | ±0.5 | ±0.3 | ±0.6 | ±0.6 | ±0.4 | ±0.3 |
Gain by Beam Tilt, average, dBi | 0 ° | 17.5 5 ° | 17.6 10 ° | 17.5 | 0 ° | 17.9 5 ° | 18.1 10 ° | 18.0 | 0 ° | 17.0 4 ° | 17.1 8 ° | 17.1 | 0 ° | 17.6 4 ° | 17.8 8 ° | 17.7 | 0 ° | 17.8 4 ° | 18.0 8 ° | 18.0 | 0 ° | 18.3 4 ° | 18.5 8 ° | 18.2 |
Beamwidth, Horizontal Tolerance, degrees | ±1.1 | ±2.1 | ±5.2 | ±4.2 | ±5 | ±2.5 |
Beamwidth, Vertical Tolerance, degrees | ±0.5 | ±0.3 | ±0.2 | ±0.2 | ±0.3 | ±0.2 |
USLS, beampeak to 20° above beampeak, dB | 18 | 15 | 15 | 15 | 16 | 16 |
Front-to-Back Total Power at 180° ± 30°, dB | 24 | 25 | 24 | 28 | 27 | 27 |
CPR at Boresight, dB | 25 | 20 | 15 | 17 | 18 | 17 |
Mechanical Specifications
Effective Projective Area (EPA), frontal | 1.4 m² | 15.069 ft² |
Effective Projective Area (EPA), lateral | 0.3 m² | 3.229 ft² |
Mechanical Tilt Range | 0°–10° |
Wind Loading @ Velocity, frontal | 1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h) |
Wind Loading @ Velocity, lateral | 315.0 N @ 150 km/h (70.8 lbf @ 150 km/h) |
Wind Loading @ Velocity, maximum | 1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h) |
Wind Loading @ Velocity, rear | 1,304.0 N @ 150 km/h (293.2 lbf @ 150 km/h) |
Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and Weights
Width, packed | 526 mm | 20.709 in |
Depth, packed | 283 mm | 11.142 in |
Length, packed | 2604 mm | 102.520 in |
Weight, gross | 59 kg | 130.073 lb |
Regulatory Compliance/Certifications
Agency | Classification |
ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
General Specifications
Antenna Type | Sector |
Band | Multiband |
Color | Light Gray (RAL 7035) |
Grounding Type | RF connector body grounded to reflector and mounting bracket |
Performance Note | Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN |
Radome Material | Fiberglass, UV resistant |
Radiator Material | Aluminum | Low loss circuit board |
Reflector Material | Aluminum |
RF Connector Interface | 4.3-10 Female |
RF Connector Location | Bottom |
RF Connector Quantity, high band | 4 |
RF Connector Quantity, low band | 2 |
RF Connector Quantity, total | 6 |
Remote Electrical Tilt (RET) Information
RET Interface | 8-pin DIN Female | 8-pin DIN Male |
RET Interface, quantity | 2 female | 2 male |
Input Voltage | 10–30 Vdc |
Internal Bias Tee | Port 1 | Port 3 |
Internal RET | High band (1) | Low band (1) |
Power Consumption, idle state, maximum | 1 W |
Power Consumption, normal conditions, maximum | 10 W |
Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
Width | 457 mm | 17.992 in |
Depth | 178 mm | 7.008 in |
Length | 2437 mm | 95.945 in |
Net Weight, without mounting kit | 40 kg | 88.185 lb |
Electrical Specifications
Impedance | 50 ohm |
Operating Frequency Band | 698 – 896 MHz | 1695 – 2360 MHz |
Polarization | ±45° |
Total Input Power, maximum | 800 W @ 50 °C |
Electrical Specifications
Frequency Band, MHz | 698–806 | 806–896 | 1695–1880 | 1850–1990 | 1920–2200 | 2300–2360 |
Gain, dBi | 17.9 | 18.2 | 17.6 | 18.0 | 18.3 | 18.7 |
Beamwidth, Horizontal, degrees | 47 | 42 | 62 | 62 | 66 | 66 |
Beamwidth, Vertical, degrees | 9 | 8.1 | 5.7 | 5.3 | 5 | 4.5 |
Beam Tilt, degrees | 0–10 | 0–10 | 0–8 | 0–8 | 0–8 | 0–8 |
USLS (First Lobe), dB | 18 | 21 | 17 | 19 | 20 | 20 |
Front-to-Back Ratio at 180°, dB | 33 | 39 | 33 | 35 | 35 | 35 |
Isolation, Cross Polarization, dB | 25 | 25 | 25 | 25 | 25 | 25 |
Isolation, Inter-band, dB | 30 | 30 | 28 | 28 | 28 | 28 |
VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
PIM, 3rd Order, 2 x 20 W, dBc | -153 | -153 | -153 | -153 | -153 | -153 |
Input Power per Port at 50°C, maximum, watts | 300 | 300 | 250 | 250 | 250 | 200 |
Electrical Specifications, BASTA
Frequency Band, MHz | 698–806 | 806–896 | 1695–1880 | 1850–1990 | 1920–2200 | 2300–2360 |
Gain by all Beam Tilts, average, dBi | 17.6 | 18.1 | 17.1 | 17.7 | 18.0 | 18.4 |
Gain by all Beam Tilts Tolerance, dB | ±0.5 | ±0.3 | ±0.6 | ±0.6 | ±0.4 | ±0.3 |
Gain by Beam Tilt, average, dBi | 0 ° | 17.5; 5 ° | 17.6; 10 ° | 17.5 | 0 ° | 17.9; 5 ° | 18.1; 10 ° | 18.0 | 0 ° | 17.0; 4 ° | 17.1; 8 ° | 17.1 | 0 ° | 17.6; 4 ° | 17.8; 8 ° | 17.7 | 0 ° | 17.8; 4 ° | 18.0; 8 ° | 18.0 | 0 ° | 18.3; 4 ° | 18.5; 8 ° | 18.2 |
Beamwidth, Horizontal Tolerance, degrees | ±1.1 | ±2.1 | ±5.2 | ±4.2 | ±5 | ±2.5 |
Beamwidth, Vertical Tolerance, degrees | ±0.5 | ±0.3 | ±0.2 | ±0.2 | ±0.3 | ±0.2 |
USLS, beampeak to 20° above beampeak, dB | 18 | 15 | 15 | 15 | 16 | 16 |
Front-to-Back Total Power at 180° ± 30°, dB | 24 | 25 | 24 | 28 | 27 | 27 |
CPR at Boresight, dB | 25 | 20 | 15 | 17 | 18 | 17 |
Mechanical Specifications
Effective Projective Area (EPA), frontal | 1.4 m² | 15.069 ft² |
Effective Projective Area (EPA), lateral | 0.3 m² | 3.229 ft² |
Mechanical Tilt Range | 0°–10° |
Wind Loading @ Velocity, frontal | 1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h) |
Wind Loading @ Velocity, lateral | 315.0 N @ 150 km/h (70.8 lbf @ 150 km/h) |
Wind Loading @ Velocity, maximum | 1,485.0 N @ 150 km/h (333.8 lbf @ 150 km/h) |
Wind Loading @ Velocity, rear | 1,304.0 N @ 150 km/h (293.2 lbf @ 150 km/h) |
Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and Weights
Width, packed | 526 mm | 20.709 in |
Depth, packed | 283 mm | 11.142 in |
Length, packed | 2604 mm | 102.520 in |
Weight, gross | 59 kg | 130.073 lb |
Click on image to enlarge. |
Click on image to enlarge. |
Regulatory Compliance/Certifications
Agency | Classification |
ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
Documentation & Downloads
Assembly Drawing
Installation Instruction
Product Information
Product Specification
Warranty
Assembly Drawing
Installation Instruction
Product Compliance Documentation
Product Information
Product Specification
Warranty
Other Ways to Browse