For other alternatives, please contact us for more information.

0 Alternative products available

NHHS4-45A-R3B

14 Port Sector Antenna, 2x 698-896 MHz, 4x 1695-2360 MHz 45° HPBW, and 8x 3400-3550/3700-4000 MHz Beamformer, 3x RETs and 3x SBTs

Find a Partner

Specifications

Finish making your selections or clear them to view relevant specifications.

Features and Benefits

Narrow beamwidth capacity antenna for higher level of densification and enhanced data throughput
Internal SBT on low and high band allow remote RET control from the radio over the RF jumper cable
Separate RS-485 RET input/output for low and high band
One LB RET, one MB RET and one HB RET. Both mid bands are controlled by one RET to ensure same tilt level for 4x Rx or 4x MIMO

Specifications

General Specifications

Antenna Type	Sector and beamforming
Band	Multiband
Calibration Connector Interface	4.3-10 Female
Calibration Connector Quantity	1
Color	Light Gray (RAL 7035)
Grounding Type	RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note	Outdoor usage
Radome Material	Fiberglass, UV resistant
Radiator Material	Low loss circuit board
Reflector Material	Aluminum
RF Connector Interface	4.3-10 Female
RF Connector Location	Bottom
RF Connector Quantity, high band	8
RF Connector Quantity, mid band	4
RF Connector Quantity, low band	2
RF Connector Quantity, total	14

Remote Electrical Tilt (RET) Information

RET Hardware	CommRET v2
RET Interface	8-pin DIN Female \| 8-pin DIN Male
RET Interface, quantity	3 female \| 3 male
Input Voltage	10–30 Vdc
Internal Bias Tee	Cal Port \| Port 1 \| Port 3
Internal RET	High band (1) \| Low band (1) \| Mid band (1)
Power Consumption, active state, maximum	10 W
Power Consumption, idle state, maximum	2 W
Protocol	3GPP/AISG 2.0

Dimensions

Width	498 mm \| 19.606 in
Depth	197 mm \| 7.756 in
Length	1399 mm \| 55.079 in
Net Weight, antenna only	29 kg \| 63.934 lb

Array Layout

Click on image to enlarge.

Port Configuration

Click on image to enlarge.

Electrical Specifications

Impedance	50 ohm
Operating Frequency Band	698 – 896 MHz \| 1695 – 2360 MHz \| 3400 – 4000 MHz
Polarization	±45°
Total Input Power, maximum	1,040 W @ 50 °C

Electrical Specifications

	R1	R1	Y1,Y2	Y1,Y2	Y1,Y2	Y1,Y2	P1	P1
Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
RF Port	1,2	1,2	3-6	3-6	3-6	3-6	7-14	7-14
Gain, dBi	15.3	15.7	18.1	18.3	19.0	19.6	16.1	17.5
Beamwidth, Horizontal, degrees	46	41	48	46	44	40	84	71
Beamwidth, Vertical, degrees	19	17	7.6	7.1	6.7	5.9	6.2	5.7
Beam Tilt, degrees	2–18	2–18	1–9	1–9	1–9	1–9	0–10	0–10
USLS (First Lobe), dB	16	17	17	17	17	20	14	15
Front-to-Back Ratio at 180°, dB	34	36	36	35	34	34	29	30
Coupling level, Amp, Antenna port to Cal port, dB							26	26
Coupling level, max Amp Δ, Antenna port to Cal port, dB							±2	±2
Coupler, max Amp Δ, Antenna port to Cal port, dB							0.9	0.9
Coupler, max Phase Δ, Antenna port to Cal port, degrees							7	7
Isolation, Cross Polarization, dB	25	25	25	25	25	25	25	25
Isolation, Inter-band, dB	25	25	25	25	25	25	25	25
Isolation, Co-polarization, dB							19	19
VSWR \| Return loss, dB	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0
PIM, 3rd Order, 2 x 20 W, dBc	-153	-153	-153	-153	-153	-153	-145	-145
Input Power per Port at 50°C, maximum, watts	300	300	250	250	250	250	75	75

Electrical Specifications, Broadcast 45

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Beamwidth, Vertical, degrees							6.2	5.8
Front-to-Back Total Power at 180° ± 30°, dB							27	25
USLS (First Lobe), dB							17	20

Electrical Specifications, Broadcast 65

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Gain, dBi							17.1	18.2
Beamwidth, Horizontal, degrees							65	65
Beamwidth, Vertical, degrees							6.2	5.8
Front-to-Back Total Power at 180° ± 30°, dB							26	24
USLS (First Lobe), dB							17	19

Electrical Specifications, Service Beam

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Steered 0° Gain, dBi							20.4	21.6
Steered 0° Beamwidth, Horizontal, degrees							27	23
Steered 0° Front-to-Back Total Power at 180° ± 30°, dB							29	29
Steered 0° Horizontal Sidelobe, dB							13	13
Steered 0° USLS (First Lobe), dB							18	21
Steered 30° Gain, dBi							19.4	19.9
Steered 30° Beamwidth, Horizontal, degrees							31	31
Steered 30° Front-to-Back Total Power at 180° ± 30°, dB							27	27

Electrical Specifications, Soft Split

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Gain, dBi							19.3	20.2
Beamwidth, Horizontal, degrees							36	32
Front-to-Back Total Power at 180° ± 30°, dB							27	27
Horizontal Sidelobe, dB							15	16
USLS (First Lobe), dB							18	21

Mechanical Specifications

Wind Loading @ Velocity, frontal	461.0 N @ 150 km/h (103.6 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral	137.0 N @ 150 km/h (30.8 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum	554.0 N @ 150 km/h (124.5 lbf @ 150 km/h)
Wind Loading @ Velocity, rear	318.0 N @ 150 km/h (71.5 lbf @ 150 km/h)
Wind Speed, maximum	241 km/h (150 mph)

Packaging and Weights

Width, packed	565 mm \| 22.244 in
Depth, packed	309 mm \| 12.165 in
Length, packed	1587 mm \| 62.480 in
Weight, gross	41.4 kg \| 91.271 lb

Regulatory Compliance/Certifications

Agency	Classification
ROHS	Compliant/Exempted
CHINA-ROHS	Above maximum concentration value
UK-ROHS	Compliant/Exempted

General Specifications

Antenna Type	Sector and beamforming
Band	Multiband
Calibration Connector Interface	4.3-10 Female
Calibration Connector Quantity	1
Color	Light Gray (RAL 7035)
Grounding Type	RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note	Outdoor usage
Radome Material	Fiberglass, UV resistant
Radiator Material	Low loss circuit board
Reflector Material	Aluminum
RF Connector Interface	4.3-10 Female
RF Connector Location	Bottom
RF Connector Quantity, high band	8
RF Connector Quantity, mid band	4
RF Connector Quantity, low band	2
RF Connector Quantity, total	14

Remote Electrical Tilt (RET) Information

RET Hardware	CommRET v2
RET Interface	8-pin DIN Female \| 8-pin DIN Male
RET Interface, quantity	3 female \| 3 male
Input Voltage	10–30 Vdc
Internal Bias Tee	Cal Port \| Port 1 \| Port 3
Internal RET	High band (1) \| Low band (1) \| Mid band (1)
Power Consumption, active state, maximum	10 W
Power Consumption, idle state, maximum	2 W
Protocol	3GPP/AISG 2.0

Dimensions

Width	498 mm \| 19.606 in
Depth	197 mm \| 7.756 in
Length	1399 mm \| 55.079 in
Net Weight, antenna only	29 kg \| 63.934 lb

Electrical Specifications

Impedance	50 ohm
Operating Frequency Band	698 – 896 MHz \| 1695 – 2360 MHz \| 3400 – 4000 MHz
Polarization	±45°
Total Input Power, maximum	1,040 W @ 50 °C

Electrical Specifications

	R1	R1	Y1,Y2	Y1,Y2	Y1,Y2	Y1,Y2	P1	P1
Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
RF Port	1,2	1,2	3-6	3-6	3-6	3-6	7-14	7-14
Gain, dBi	15.3	15.7	18.1	18.3	19.0	19.6	16.1	17.5
Beamwidth, Horizontal, degrees	46	41	48	46	44	40	84	71
Beamwidth, Vertical, degrees	19	17	7.6	7.1	6.7	5.9	6.2	5.7
Beam Tilt, degrees	2–18	2–18	1–9	1–9	1–9	1–9	0–10	0–10
USLS (First Lobe), dB	16	17	17	17	17	20	14	15
Front-to-Back Ratio at 180°, dB	34	36	36	35	34	34	29	30
Coupling level, Amp, Antenna port to Cal port, dB							26	26
Coupling level, max Amp Δ, Antenna port to Cal port, dB							±2	±2
Coupler, max Amp Δ, Antenna port to Cal port, dB							0.9	0.9
Coupler, max Phase Δ, Antenna port to Cal port, degrees							7	7
Isolation, Cross Polarization, dB	25	25	25	25	25	25	25	25
Isolation, Inter-band, dB	25	25	25	25	25	25	25	25
Isolation, Co-polarization, dB							19	19
VSWR \| Return loss, dB	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0
PIM, 3rd Order, 2 x 20 W, dBc	-153	-153	-153	-153	-153	-153	-145	-145
Input Power per Port at 50°C, maximum, watts	300	300	250	250	250	250	75	75

Electrical Specifications, Broadcast 45

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Beamwidth, Vertical, degrees							6.2	5.8
Front-to-Back Total Power at 180° ± 30°, dB							27	25
USLS (First Lobe), dB							17	20

Electrical Specifications, Broadcast 65

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Gain, dBi							17.1	18.2
Beamwidth, Horizontal, degrees							65	65
Beamwidth, Vertical, degrees							6.2	5.8
Front-to-Back Total Power at 180° ± 30°, dB							26	24
USLS (First Lobe), dB							17	19

Electrical Specifications, Service Beam

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Steered 0° Gain, dBi							20.4	21.6
Steered 0° Beamwidth, Horizontal, degrees							27	23
Steered 0° Front-to-Back Total Power at 180° ± 30°, dB							29	29
Steered 0° Horizontal Sidelobe, dB							13	13
Steered 0° USLS (First Lobe), dB							18	21
Steered 30° Gain, dBi							19.4	19.9
Steered 30° Beamwidth, Horizontal, degrees							31	31
Steered 30° Front-to-Back Total Power at 180° ± 30°, dB							27	27

Electrical Specifications, Soft Split

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	2300–2360	3400–3550	3700–4000
Gain, dBi							19.3	20.2
Beamwidth, Horizontal, degrees							36	32
Front-to-Back Total Power at 180° ± 30°, dB							27	27
Horizontal Sidelobe, dB							15	16
USLS (First Lobe), dB							18	21

Mechanical Specifications

Wind Loading @ Velocity, frontal	461.0 N @ 150 km/h (103.6 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral	137.0 N @ 150 km/h (30.8 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum	554.0 N @ 150 km/h (124.5 lbf @ 150 km/h)
Wind Loading @ Velocity, rear	318.0 N @ 150 km/h (71.5 lbf @ 150 km/h)
Wind Speed, maximum	241 km/h (150 mph)